
Two buyers can order “200 mesh” and “200 micron” in the same week, receive two completely different products, and blame the supplier. The first has openings of about 74 microns. The second has openings of 200 microns. That is a factor of nearly three in particle size, and in a bottling line it is the difference between a compliant retail product and honey that has had a constituent legally defined as part of honey strained out of it.
This is written for honey houses and for the importers who specify their equipment. It sets out what micron and mesh actually measure, what the Codex standard and European rules permit you to remove, how a three-stage line works in practice, and where filtration stops being a clarity decision and becomes a compliance one.
Micron and mesh are not the same unit
A micron is one millionth of a metre. A micron rating on a filter describes the size of the opening. A mesh count describes how many openings there are per linear inch. Because the wire between the openings takes up space, mesh count and opening size are related but not interchangeable, and the opening also depends on wire diameter.
Published conversion charts for standard square-weave stainless wire cloth give the following. Treat these as nominal geometry, not as a guaranteed filtration rating: a mesh number alone is incomplete without the wire diameter, and the same mesh count woven with a different wire gives a different opening.
| US mesh count | Nominal opening (micron) | Nominal opening (mm) | Note for buyers |
|---|---|---|---|
| 20 | 841 | 0.841 | Coarser than any honey strainer; screening only |
| 40 | 420 | 0.420 | Close to the coarse end of honey pre-filtration |
| 60 | 250 | 0.250 | Coarse pre-filter territory |
| 80 | 177 | 0.177 | Between the 200 and 150 micron honey stages |
| 100 | 149 | 0.149 | Finer than the finest common honey stage |
| 200 | 74 | 0.074 | Roughly a third of “200 micron”; this is where pollen retention starts |
| 400 | 37 | 0.037 | Below the pore size used to test water-insoluble content; do not use on retail honey |
Open area matters as much as opening size. Published geometry for a 200-mesh square weave with 0.05 mm wire puts the open area near 36.8 percent, which means roughly two thirds of the surface is metal. That is why flow collapses as the mesh gets finer, and why a filter that looks adequate on a bench can stall a line. When you specify a mesh, specify mesh count, wire diameter and grade together.
What the standard permits you to remove
The Revised Codex Standard for Honey, CODEX STAN 12-1981, Rev.1 (1987), Rev.2 (2001), states in section 3.1 that honey sold as such shall not have added to it any food ingredient, and that no pollen or constituent particular to honey may be removed except where this is unavoidable in the removal of foreign inorganic or organic matter. Section 3.2 adds that honey shall not be heated or processed to such an extent that its essential composition is changed or its quality impaired.
European law says the same thing. Directive 2014/63/EU, amending Council Directive 2001/110/EC relating to honey, records in its first recital that the Directive prohibits the removal of any constituent particular to honey, including pollen, unless that removal is unavoidable in the removal of foreign matter, and that these requirements are in line with the Codex standard.
The measurable limit is the water-insoluble solids content. Codex sets it at not more than 0.1 g per 100 g for honeys other than pressed honey, and not more than 0.5 g per 100 g for pressed honey. European Commission Joint Research Centre guidance on honey production confirms the same limits and describes how they are tested: the water-insoluble content is measured by filtering a honey solution through a glass crucible with a pore size of 15 to 40 microns, and the insoluble fraction includes pollen, honeycomb debris, and bee and dirt particles.
Put those two facts together and the design boundary appears. The compliance test filters at 15 to 40 microns. Any production filter finer than that is approaching the point where it removes what the test measures. The same JRC guidance gives maize pollen grains an average diameter of 70 to 125 microns, so a 200 micron screen passes maize pollen freely, while a 200 mesh screen at 74 microns would retain a meaningful share of it. Supplier guidance elsewhere quotes an average pollen grain nearer 25 microns, which does not reconcile with the maize figure and is exactly why pollen size must be treated as species-dependent rather than as a single number.
For a working rule: strain to remove foreign matter, do not filter to strip the honey, and if a customer asks for ultrafine filtration for a retail product, get the legal position in the destination market confirmed in writing before you ship the mesh.
600, 400 and 200 micron in a real line
The commercial convention is a descending cascade. Honey leaves the extractor carrying wax cappings, propolis specks, wood slivers from frame work and bee parts. One fine filter asked to do all of that work clogs in minutes.
| Stage | Rating | What it removes | Flow behaviour | When to stop at this stage |
|---|---|---|---|---|
| First pass, coarse | 600 micron, sometimes 800 | Wax chunks, large capping pieces, bee parts, frame debris | Fastest stage; protects everything downstream | Stop here for honey sold as raw or minimally processed |
| Second pass, medium | 400 micron | Smaller wax flakes and visible particles | Moderate; the usual balance of speed against clarity | Stop here for most farm-gate and farmers-market sales |
| Third pass, fine | 200 micron | Fine suspended particles that cause visible haze | Slowest; clogs first and needs scraping or swapping | Use for retail clarity in bright glass |
| Settling | No mesh | Air bubbles and the finest wax film, removed as a skim | 24 to 48 hours standing in a covered tank | Always, before bottling |
On timing, one supplier of a three-stage bucket strainer states that each stage adds roughly 5 to 10 minutes to filtering warm honey in a five-gallon bucket, with the finest stage slowest. A five-gallon bucket is about 19 litres, so that is a derived throughput of roughly 2 to 4 litres per minute per stage. Applied to a 200-litre settling tank, one pass through a single stage would run on the order of 50 to 100 minutes. Those are derived figures from a retailer’s stated bucket timing, not measurements from a production line; time your own honey at your own temperature before you schedule a shift.
Temperature drives everything above. Filtration guidance commonly puts the working window at roughly 35 to 38 degrees Celsius for fine filtration, with extraction itself handled nearer 27 to 35 degrees Celsius, and warns that exceeding about 43 degrees Celsius begins to degrade enzymes and aroma compounds. Warm honey flows; cold honey does not, and the usual operator response to cold honey is to push harder, which is how mesh gets damaged and particles get forced through.
After the last stage, settle. Guidance for bottling calls for at least 24 hours standing in a covered tank so that air bubbles and the finest wax particles rise into a thin skim, which is then removed rather than stirred back in. Practitioner accounts extend that to 24 to 48 hours. The skim is the difference between honey that looks clean in a bucket and honey that looks clean in a jar.

Choosing the hardware
Three decisions determine whether a strainer survives a season.
Mesh material and grade. Stainless steel mesh in a rigid frame is washable, reusable and dimensionally stable, which matters because a nylon bag stretches and its effective opening grows as it loads. Nylon has one advantage: a conical bag gives far more surface area than a flat disc of the same diameter, so it clogs later. Most honey houses run both, a rigid stainless sieve for the first pass and a nylon cone or bag for the polish.
Frame and contact material. Everything the honey touches is a food-contact surface. In the European Union, food-contact materials are governed by Regulation (EC) No 1935/2004, which requires that materials do not transfer constituents to food in quantities that could endanger health or change composition. Ask your supplier for the stainless grade and for a declaration of compliance for the plastic frame or the nylon, not just for a micron number.
Cleaning access. A double-sieve unit with two permanently fixed meshes is fast to use and awkward to clean at the corners. Nesting strainers that lift apart clean faster and let you run one stage alone. If the honey house runs daily through a flow, choose the design that can be stripped and washed in minutes, because dried honey on a fine mesh is a full shift to remove.
Downstream, remember that filtration does not change moisture. Codex caps moisture at not more than 20 percent for most honeys, and wet bottles or a wet tank raise the water content of the finished pack. Dry every jar and every tank before filling.

When the line runs: northern and southern windows
Northern hemisphere. Across North America and Europe the extraction and bottling window runs broadly from June into September, with the heaviest weeks at the end of the main flow. Filtration equipment is bought and commissioned in the preceding winter or spring, and this is the window in which a clogged mesh or a missing spare sieve costs real volume.
Southern hemisphere. In Australia, New Zealand and southern South America the equivalent window falls roughly November into March, with regional variation in warm coastal districts. Distributors supplying those markets should land stock by October and hold spare mesh and bags, because a torn filter bag in the middle of a flow has no fast replacement.
Both hemispheres share the same failure pattern: the line is commissioned during the flow rather than before it. Run water, then run a drum of last season’s honey, before the first real harvest.

Mistakes that cost the most
| Mistake | What it looks like on the line | What it costs | What to do instead |
|---|---|---|---|
| Ordering “200 mesh” when the process calls for 200 micron | Honey that will not pass through the sieve, or honey stripped of pollen | Either a stalled line or product that risks breaching the rule that no constituent particular to honey may be removed | Specify in microns, and state mesh count and wire diameter only as the construction detail |
| Running a single fine filter with no pre-filter | The filter blinds within minutes and the operator scrapes continuously | Most of the shift spent scraping rather than filtering; mesh torn by scraping tools | Always cascade: 600 micron first, then 400, then 200 |
| Filtering cold honey and pushing to compensate | Slow flow, rising head of honey above the mesh | Distorted or split mesh, and particles forced through the openings | Warm to roughly 35 to 38 degrees Celsius and let gravity work |
| Heating past about 43 degrees Celsius to speed flow | Faster throughput, honey that fails on enzyme and aroma quality | Product downgraded, and a breach of the requirement not to process honey so as to impair its quality | Warm slowly, never directly, and never above the stated ceiling |
| Skipping the settling step | Honey that looks clear in the tank and hazy in the jar | Retail complaints and returns on appearance, which is the most visible quality signal a buyer has | Settle 24 to 48 hours, skim, then bottle |
| Specifying micron but not the material | Mesh that rusts, or a plastic frame that is not food-contact declared | Contamination risk and a failed audit at the customer’s end | State grade, frame material and a declaration of compliance in the order |
| No spare mesh held on site | One torn bag stops the line mid-flow | A day of harvest waiting on a part that costs very little | Hold at least one spare of every stage before the window opens |
The pattern across all seven is that filtration problems are specification problems. Every one of them is decided at the point of purchase, and every one of them surfaces during the two or three weeks of the year when the honey is moving.
Enzher supplies the strainers and tanks for this stage of the line. A stainless steel double-layer sieve covers the first two stages in one frame and is the usual starting point for a honey house. Where volume and surface area matter more than rigidity, a conical nylon strainer clogs later than a flat disc of the same rating, and a double-sieve plastic and nylon strainer is the lower-cost option for seasonal or satellite sites. The strainers, pails and settling tanks are grouped in the honey pail and filter category.
Standard references used here: the honey standard itself through the Codex Alimentarius text list at FAO, food-contact material rules from the European Commission’s food contact materials page, and production context from FAO’s pollination programme.