
Frame capacity is the number on the drum, and it is the number buyers argue about. It is also the least important of the three figures that decide whether a honey room keeps up with the yard. The question that matters is how many frames arrive in a single flow, how long the drum holds each load, and what happens to the honey once it leaves the gate. Sizing an extractor means answering those three, then picking the drum that fits.
This is written for operations above roughly fifty colonies and for the importers specifying equipment for them. It uses published United States production statistics, published per-frame yields and quoted machine throughputs to build a sizing method you can run on your own colony count. Where a number is quoted from a supplier rather than measured, it says so.
Start from frames per season, not from colony count
The United States Department of Agriculture’s National Agricultural Statistics Service released its 2025 honey report on 13 March 2026. It puts United States honey production at 116 million pounds from 2.41 million colonies, an average yield of 48.0 pounds per colony, down 7 percent on the previous year. State figures vary widely: North Dakota reported 490,000 colonies and an average yield of 74 pounds per colony for 2024. A national average is not a design input, but it is the only widely published yardstick, so the method below uses it and shows how to replace it with your own records.
Convert colony yield into frames. A capped deep Langstroth frame is commonly quoted at roughly 5 to 8 pounds of honey. At the 2025 national average of 48 pounds per colony, that is about 6 to 10 deep frames per colony for the season. At North Dakota’s 74 pounds, it is about 9 to 15. Note what those numbers are: they are division using two published figures, not measurements from any particular yard. Keep your own frame weights and the estimate disappears.
Then correct for the fact that the crop does not arrive evenly. In most commercial operations a large share of the season’s honey comes in one or two flows. If sixty percent of a 500-colony crop lands in a single flow, that flow is somewhere between 1,800 and 3,000 frames, and it has to be processed in days, not months. Size the extractor for the peak flow, not the annual total. This is the single most common sizing error, and it is why yards with adequate annual capacity still lose honey every good spring.
Frame format decides the drum before capacity does
A frame is not a frame. Deep brood frames, medium supers and shallow supers differ in height, and a radial basket built for medium super frames will not take full-depth brood frames safely. One European radial model, for example, is specified around super frames of roughly 48 by 16 centimetres and is described as optimised for Dadant, Langstroth and similar formats at that height, with the manufacturer noting that operations running full-depth or Layens frames need a different machine. Ask what frame the basket was built for before asking how many it holds.
| Frame class | Typical dimensions or standard | Effect on drum choice | Specify in the purchase order |
|---|---|---|---|
| Full-depth Langstroth or Dadant brood frame | Brood depth; the tallest standard format | Needs a tall drum and a taller basket; raises drum diameter and motor torque requirement | Frame length and depth in mm, and whether the basket is reversible |
| Medium super frame | Roughly 48 cm by 16 cm in European specification | Most radial baskets are built for this height; the best frames-per-cycle for a given drum diameter | Basket height and top-bar seating, not just frame count |
| Shallow super frame | Shallower than medium; regional | Fits some medium baskets with a spacer; check that the frame cannot drop | Whether a spacer or adapter is supplied |
| Layens, Dadant-Blatt and other non-Langstroth formats | Regional standards across Spain, France, Eastern Europe and Latin America | Usually needs a dedicated basket; a Langstroth drum may spin the frame but the support is wrong | Send a physical frame with the order |
Frame count quoted by a supplier always assumes a frame class. A “20-frame” machine is a 20-medium-frame machine unless the listing says otherwise. Distributors selling into markets with a different dominant standard should confirm basket geometry in writing, because a drum that fits the wrong frame is a total loss, not a partial one.
Throughput: the number on the drum is not the number on the clock
Two extractors with the same frame count can differ by a factor of three in output, because the cycle is made of spin time plus handling time, and only one of those is on the specification sheet.
| Extractor class | Quoted throughput (frames per hour) | Source and standing | What the figure includes |
|---|---|---|---|
| Hand-cranked manual, 2 to 4 frames | About 4 to 6 | Supplier guidance, small-scale class | Cranking, load and unload by one operator; excludes uncapping |
| Electric, 4 frames | About 20 to 30 medium frames | Retailer guidance; quoted with one person uncapping and one loading | Two operators; assumes a reversible or radial basket |
| Electric, small commercial class | About 20 to 40 | Supplier listing, operator-dependent | Intermittent duty cycle; varies with honey viscosity |
| Radial, 18 medium supers | A full 8 to 10 minute cycle empties 18 frames | European retailer product description | One load; operator free to uncap the next batch during the cycle |
| Radial, commercial | Commonly 8 frames to more than 80 per basket | Supplier guidance on basket range | No manual flipping; higher frames per cycle |
The 18-frame radial figure is the useful one to reason with. At an 8 to 10 minute cycle, one machine turns through 108 to 135 frames per hour if the operator can load and unload fast enough to keep it spinning. That is roughly five times the quoted output of a small electric machine, and the reason is not speed: it is that a radial basket empties both comb faces in one direction, so nobody stops to flip eighteen frames by hand. A tangential basket of the same count would need a stop, a flip and a second run.
Two operational points sit behind every throughput figure. Honey temperature governs viscosity; guidance for extraction puts the working range at roughly 27 to 35 degrees Celsius, and cold honey slows flow dramatically. And speed has to be ramped, not switched on: radial machines are commonly run at 200 to 350 rpm at full speed, but starting at full speed on heavy, soft comb is the standard cause of comb blowout. A ramp that starts low and builds over 30 to 60 seconds is the practice every source agrees on.

Sizing band by band
The table below applies the method: frames per season from colony count at 6 to 10 deep frames per colony, a suggested radial basket size, the resulting load count, and the season hours at the quoted 20 to 30 frames per hour band for electric machines. Every cell is derived arithmetic on the figures cited above, not measured output.
| Colony count | Frames per season (derived) | Suggested radial capacity (frames) | Loads per season (derived) | Season hours at 20 to 30 frames/h | Practical note |
|---|---|---|---|---|---|
| 50 | 300 to 500 | 3 to 4 | 75 to 167 | 10 to 25 h | A 4-frame electric is the usual answer; manual is viable under about 20 colonies |
| 150 | 900 to 1500 | 6 to 9 | 100 to 250 | 30 to 75 h | First band where radial beats tangential on labour |
| 500 | 3000 to 5000 | 12 to 20 | 150 to 417 | 100 to 250 h | Size for the peak flow, 1800 to 3000 frames, not the annual total |
| 1500 | 9000 to 15000 | 24 to 40 | 225 to 625 | 300 to 750 h | Two machines beat one large one; downtime on a single drum stalls the yard |
Read the last column against the clock you actually have. For a 500-colony yard, 100 to 250 hours of extraction is a fortnight of one full-time operator, or roughly three to five weeks of part-time honey-room work if the peak flow is spread. If your flow is shorter than that, the drum is too small, and no amount of operator effort fixes it.
The same arithmetic run on a manual machine makes the point sharply. At 4 to 6 frames per hour, the 500-colony season is 500 to 1,250 hours. That is most of a working year for one person, spent cranking. Manual extractors are the right purchase for remote sites without power and for operations below about twenty colonies. Above that, the labour line outweighs the equipment line.
Where the bottleneck moves after you fix the drum
Once capacity is right, four other stations set the pace, and any of them can waste the investment in a larger drum.
Uncapping. A radial that empties eighteen frames in nine minutes needs eighteen frames uncapped and staged every nine minutes. Hand knives do not sustain that. If the drum is large, specify the uncapping station at the same time, and check whether a powered uncapping machine’s stated comb-thickness range matches your frames.
Warming. Supers held at 27 to 35 degrees Celsius extract faster and more completely. A warm room is cheaper than a bigger extractor.
The gate and the drain path. A bottom honey gate that cannot discharge as fast as the drum fills throttles the whole cycle. Check the gate bore, the height of the legs, and whether a strainer and a settling tank fit underneath.
Filtration and settling. Honey leaving the extractor needs straining before it goes to a tank. A double sieve or a staged strainer set at 600, 400 and 200 microns is the usual first pass, and the tank downstream has to be food-grade and lidded. If the tank is smaller than one flow, the extractor stops while you bottle.
Power and duty cycle. Small electric machines are built for intermittent duty. A machine run continuously through a full day of a heavy flow needs a motor and drive specified for that. Ask the supplier for the duty rating in writing, and confirm the supply voltage: most machines in this class are built for 220 volt single-phase.
Seasonality: when the frame count is tested
Northern hemisphere. In North America and Europe the main flow runs broadly May into July, with a second, smaller flow in late summer in some regions. Extraction happens at the end of that window, which means the machine has to be landed, installed and test-run before May. Orders placed in spring arrive after the flow they were bought for.
Southern hemisphere. In Australia, New Zealand and southern South America the equivalent window falls roughly September into December, with later flows into autumn in warm coastal districts. Distributors in those markets should have stock landed by August, and should hold spare drive parts before the window opens, because a failed motor in November costs the season.
Both hemispheres share one rule: the honey room is specified in the off-season and tested before the flow, not during it. Run a full load of water or of old comb through a new machine before the first real harvest.

Sizing an extractor: the short version
Take your own colony count and your own average yield per colony. Divide by the honey weight of one of your capped frames to get frames per season. Take the share of the crop that arrives in your biggest single flow, and size for that number, not the annual total. Then divide by the throughput band your machine class actually achieves, and check the hours against the days your flow lasts.
Choose frame capacity from that, and choose the basket type from your frame format. Radial baskets win above roughly twenty to thirty production colonies because they remove the flip step; tangential baskets remain the right answer for small operations, for viscous honey where a stronger single-face extraction helps, and for buyers whose priority is entry price rather than throughput.
Then specify the rest of the line to match: uncapping capacity, a warm room, a gate that discharges fast enough, a strainer set and a settling tank that holds one flow. The drum is only as fast as the slowest station after it.
Material and finish belong in the same specification. Food-contact grade stainless is the expectation for commercial extraction equipment, and older tin-plated drums do not meet it. Ask for the grade, the weld finish, the basket material and the spare parts list, not just the frame count.
Enzher builds extractors across the full band described above. A 3-frame manual extractor is the entry point for operations under twenty colonies and for remote sites. A 4-frame electric machine with variable speed is the step that removes cranking and lets the operator ramp gently to protect comb. Above that, a 12-frame automatic electric extractor is the practical size for yards running several hundred colonies. The full range, including larger radial units, sits in the honey extractor category.
Production and colony statistics in this piece come from the USDA NASS bee and honey surveys, with trade and production context available through FAOSTAT and FAO’s pollination programme.